联系电话:

010-5601-7676

您当前位置:www.4166.com>工程动态工程动态

天花龙骨安装工艺诠释

发表时间:2016-12-07 10:06:39 发表编辑:phpcms 浏览次数:

第一步:软膜天花龙骨安装
The first step: piamater ceiling keel installation
根据图纸设计要求,在需要安装软膜天花的水平高度位置四周围固定一圈4X4Cm支撑龙骨(有些地方面积比较大时要求分块安装,以达到良好效果.这样就需要中间位置加一根木方条子)。
According to the requirements of design drawings, the position of the height level around the need to install piamater ceiling around a ring of 4X4Cm fixed support keel (some local area is large block installation requirements, in order to achieve good results. This requires the middle position plus a wooden note).
当所有需要木方条子固定好之后,然后在支撑龙骨的底面固定安装软膜天花的铝合金龙骨。
When all the required wood sliver fixed, and then in the Aluminum Alloy keel support keel bottom fixed installation soft film ceiling.
第二步软膜天花安装:
The second step installation of soft film smallpox:
当所有的安装软膜天花的铝合金龙骨固定好以后,再安装软膜。先把软膜打开用专用的加热风炮充分加热均匀,然后用专用的插刀把软膜张紧插到铝合金龙骨上,最后把四周多出的软膜修剪完整即可。
When all the Aluminum Alloy keel installation soft film ceiling fixed after installing film. The film opened with a special heating air full uniform heating, and then use a dedicated knife inserted film tensioning is inserted into the Aluminum Alloy keel, the film can be more around the complete pruning.
安装完毕后,用干净毛巾把软膜天花清洁干净。
After installation, with a clean towel to clean soft film smallpox.
常识拓展:软膜天花施工注意事项
The expansion of knowledge: piamater ceiling construction notice
安装前先到工地现场检查是否有条件安装龙骨,现场墙身是否完成,木工部分加工是否合格,需要抹灰部分先完成,特别注意木工部分一定要按照要求来做,灯、风口等开孔尺寸要提前加工好。
Before installation to the site to check whether the conditions of the keel wall, the scene is completed, woodworking processing part is qualified, need to pay special attention to the first part of plastering, carpentry part must be in accordance with the requirements to do, to advance the processing hole size, light air etc..
现场条件许可方进场施工,首先要按图纸设计要求的木工做好部分进行固定铝合金龙骨龙骨,注意角位一定要直角平整光滑,驳接要平、密。
Field conditions permit construction, first of all, according to the requirements of the drawing design carpentry do some of the fixed aluminum alloy keel keel, attention to the corner must be flat smooth, and the barge to flat, dense.
注意灯架、风口、光管盘要与周边的龙骨水平,并且要求牢固平稳不能摇摆方可。
Pay attention to the lamp holder, air port, light tube plate to the level of the surrounding keel, and requires a stable and smooth can not swing.
烟感、吸顶灯,先定位再做一个木底架,木底架底面要打磨光滑,并注意水平高度,太低就容易凸现底架的痕迹。
The smoke, ceiling lamps, the first position to make a wooden frame wooden chassis underside to polish, and pay attention to the level of height is too low, it is easy to show a trace.
安装天花之前,认真检查龙骨接头是否牢固和光滑,喷淋头要粘上白胶带,风口要处理好。
Before the installation of smallpox, carefully check the keel joint is firm and smooth, spray head to stick on the white tape, the outlet should be handled well.
安装天花时要先从中间往两边固定,同时注意两边尺寸,注意焊接缝要直最后做角位,注意要平整光滑。四周做好后把多出的天花修剪去除。达到完美的收边效果。
When installing smallpox, should first from the middle to both sides fixed, at the same time pay attention to both sides of the size, pay attention to the welding seam should be straight to the final corner, pay attention to smooth and smooth. Around to do a good job after the removal of the smallpox pruning. To achieve the perfect side effect.
开灯孔要在灯孔的位置上做好记号,把PVC灯圈小心准确地粘在软膜的底面,待牢固后把多出的天花去除即可。
Turn on the lights to make a mark in the lamp hole hole position, the PVC lamp ring carefully glued to the bottom surface of piamater accurately, to be strong after the removal of smallpox can be.
开风口、光管盘口处理就是找到风口光管盘口的位置,跟做四周一样,把软膜安装到铝合金龙骨上,注意角位要平整。做好后把多出的天花切除即可。
Open the air inlet, outlet pipe is to find the light position of the light pipe handicap handicap, like around the soft film mounted to Aluminum Alloy keel, note the angle should be smooth. Do a good job after the removal of the smallpox can be more.
最后用干净毛巾清洁软膜天花表面。
Finally, with a clean towel to clean the surface of soft film smallpox.
XML 地图 | Sitemap 地图